The dc rebirth
Elenco the dc rebirth
-
00v, and the current shows the current current parameterafter removing the digital display, the voltage is about 0operate in the case of power failure, pull the small pull switch in the lower left corner to the current regulating gear2pull the pull switch in t90v, and the current is 0on the right side (adjust current knob), you can adjust the desired current limit parameter, and display the current parameter synchronously with the digital displaypull out (dedicated current regulating insert) to the 2nd and 3rd ports of the wiring port, loosen the port screw with a screwdriver, and tighten with a screwdriver (at this time, connect to the listed power), and then connect the voltage of the meter shows 0remove the (special adjustment current plug) and insert it back into the original insert card holder5a can be adjusted in the whole processat this time, the power supply will emit a small currentpotenza nominaledigitale displayadjustable knobitem id480wvoltaggiovoltaggio1908262voltaggiovoltaggioinput - housing: ac1500v, 1min; output - case: dc500v, 1minworking environment:-10 °c ~ 50 °c; 20% ~ 90% rh (no condensation)shell material: metal case / aluminum casesize: 215 x 115 x 50mmterminal description and wiring method: l, n ac input terminal fg ground mark v+ dc output positive terminalv-dc output negative terminal adj adjustable potentiometer fine-tuning output dc voltageoperational use:(how to limit current) to adjust current?10-21a/0-16a/0-11a/0-6
Italia
4966999816894531 €
-
When a metal object approaches the detection surface of the sensor, the eddycurrent generated in the metal absorbs the energy of the oscillator, which weakens and stops the oscillationafter power-on, the light is on when metal is close to the detection range of the sensor, and the light is off when the metal leaves the detection range of the sensorthe oscillator generates an alternating electromagnetic field on the detection surface of the sensor54-1 pin connecting wires, of which the brown is the positive power line source, the blue is the negative power line, and the black is the output signal linewhen the metal object moves towards or out of the proximity switch, the signal will change automatically, so as to achieve the purpose of detectionthe sensor has three dupont female 2there is an led on the sensorthe inductive proximity switch is a low-cost method for non-contact detection of metal objectsthe two states of oscillation and stop of the oscillator are converted into electrical signals, which are converted into binary switching signals through shaping and amplification, and output after power amplificationspecification:output mode: npn three-wire normally open (non-shielded)working voltage: within dc 6-36voutput current: 300madetection object: metal/ironshell materialfeature:this is a non-embedded three-wire npn normally open metal sensorits composition is mainly composed of three major parts: amplifying output circuit, switching circuit, oscillator
Italia
5699999809265137 €
-
Insert the dc connectorlong press the metal ring to adjust the brightness, and it has the brightness memory functionwarm and gentle led lights: touch the metal ring to switch the color and turn off the lighttouch the metal ring at the bottom of the moon lamp to turn on / off the light and change color from yellow to whitebrand: decbestfeatures:- 3d printing technology: print layer by layer, restore the real appearance of the moonif your hand is too dry or the temperature is too low, the light may not respondthe white light will not shine when power is loweasy to put anywhere you like with the wood holderlong using time: 300mah built-in battery, after the full charge, the lamp can be used at least about 6 hours, a full charge takes about 2 hoursa perfect gift: express your love with this warm giftyour kids or beloved one are unable to resist this charming giftspecifications:- diameter: 15cm/591- material: pla- bulb: 1pcs white led light and 1pcs yellow led light- battery capacity: 1 x 300mah li-po battery (built-in)- charging time: about 2 hours- working time: about 6 hours at least (depends on brightness)- power supply: usbhow to use:1you can hold it on your handand its also a great decoration for your housesafe and environmentally friendly: pla material extracted from corn stalks, hard and smooth, non-toxic, odorless, environmentally friendlycharging port and switch integration: simple, beautiful and practical, easy to operate
Italia
26739999771118164 €
-
Insert the dc connector into the metal ring at the bottom of the moon lamp to charge, the red light is always on during the charginglong press the metal ring to adjust the brightness, and it has the brightness memory functiontouch the metal ring at the bottom of the moon lamp to turn on / off the light and change color from white to yellowif your hand is too dry or the temperature is too low, the light may not respondthe red light will automatically turn off when fully chargedthe white light will not shine when power is lowfeatures:3d technology- this lamp is made by innovative 3d printing technology, layer by layer stack, restore the real appearance of the moonperfect night light- white and yellow lighting color, you can switch freedom by the touch button at the bottom, comfortable glow to any roompackage included:1 x moon light1 x usb charging cable1 x solid wood scaffolddiameter size: 20cm/7brilliant design- rechargeable battery and usb charging (include cable without adapter);it brings you mystery and romance, this night light is just what you need for an out of this world lighting experiencegood gift- this lamp adopting non-toxic, odorless, environmentally friendly pldm material, it is a perfect gift to girls boys kids, your loved one or girlfriend
Italia
4641999816894531 €